Puretec Radfire RI Series User Manual Download Page 14 | Manualshive

Page: 14 / 28

background image

14

Installation & Operation Manual

Copyright © Puretec Pty Ltd 2021

Controllers

A full colour LCD screen provides the user with a detailed description of the system’s

performance in addition to providing any applicable fault messages and system diagnostics.

The Puretec RI-17KA includes a UV intensity monitor, but all controllers include an “infinite
expandability port” located on the right side of the controller. Simply plug in an optional UV

sensor module into the expandability port of a standard controller and the system will now

monitor the UV intensity of the system!

Power-up Sequence

On start up, the controller will run through a diagnostic start-up and the sequence will be

displayed as follows on the colour LCD:

Next, the controller checks for and initializes any optional modules that may be attached to

the system.

RI-6K

RI-10K
RI-17K
RI-17KA

Controllers

«
...
12
13
14
15
16
...
»

Summary of Contents for Radfire RI Series





























Reviews:

No comments

Related manuals for Radfire RI Series

Brand: Evolution Aqua Pages: 20

Brand: ATS Pages: 39

Sterilight PLATINUM SPV410-IHS22

Brand: Viqua Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands