manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT II, Operating Instructions Manual

Share
Download
PRÜFTECHNIK VIBXPERT II Operating Instructions Manual Download Page 89

3-39

VIBXPER

T II 05.2012

Recording

Ending the measurement recording

The measurement recording is ended when  

-  the stop condition is fulfilled 

-  the ESC button is pressed

-  the memory card is full

-  the maximum number of results is reached (65535).

Special cases

The recording function is used in a wide range of applications and is 

intuitive in use. However, the following special characteristics should 

be noted:  

What happens if the device shuts down due to a fault?

If the battery should run out during measurement, the device saves 

the measurement data prior to the emergency shut-off. If a fault arises 

during measurement, the saved results are retained.

Shock pulse measurement

Before beginning recording, enter the normalization parameters. This 

normalization then applies to the entire measurement duration. Note: 

rpm-controlled recording is only possible without normalization.

Trending spectrum

To be able to record the measurement values in a trending spectrum, 

the recording function is also available in the 'Machine template' 

mode. Recording is configured and started as described in the previ-

ous section. 
Special characteristics:

-  The trending spectrum is integrated in a machine template (OMNI-

TREND software).

-  In addition to the trending spectrum, the machine template can 

contain all measurement types permissible for the recording.

-  Recording is only possible in the template without a 'Production 

test' (see also p. 3-14).

-  After the recording, all actions that are triggered automatically are 

disabled in the template (e.g. starting the next task).

-  The recording configuration is not saved with the result. 

-  Multiple datasets can be added to a file.

Summary of Contents for VIBXPERT II

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands