manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT II, Operating Instructions Manual

Share
Download
PRÜFTECHNIK VIBXPERT II Operating Instructions Manual Download Page 27

2-15

VIBXPER

T II 05.2012

Getting  started  -  Basic  settings      

The route is set up hierarchically accord-
ing to the following plan:
1. Database - highest hierarchy
2. Location - factory, plant, customer
3. Train - groups of machines
4. Machine - individual machines
5. Measurement location - position of 
the measurement location
6. Measurement task - e.g. vibration 
acceleration

- 

e

naBled

: Display of machine images. The position of the measure-

ment locations and the measurement direction is indicated by 

symbols.   

- 

d

isaBled

: The route is processed in the set display mode (tree / list)

Display all hierarchies

This option applies to the tree view only. 
- 

e

naBled

:

 The tree displays all hierarchy levels.

- 

d

isaBled

:

 The tree only opens the branch with the first non-mea-

sured measurement location. 

Hide measured/ skipped hierarchies

This option applies to the tree view only. 
- 

e

naBled

:

 Measured/skipped hierarchy levels are hidden in the tree. 

- 

d

isaBled

:

  Measured/skipped hierarchy levels are displayed in the 

tree. 

Jump to next unmeasured (measurement location)

Here you can define to which measurement location the cursor should 

jump after you view a stored result and close the measurement task 

selection window.
- 

a

ctivated

: the cursor jumps to the next unmeasured measurement 

location.

- 

d

isaBled

: the cursor remains on the current measurement location.

Active Hierarchy/ Mode

The following settings determine how the tree structure should ap-

pear when opening the route / machine template:
- 

t

rain

 / m

achine

 / m

easurement

 

location

: The tree opens to the se-

lected hierarchy level*. 

- 

a

uto

: Dynamic adaptation of the tree view. The type of display 

depends on whether the route contains graphical information and 

whether the 'Graphic Route' option is enabled.

Show result

With every measurement task, older, historic measurements can be 

saved in the route and called up to compare them with current results. 
- 

s

tandard

: last measurement saved.

- 

h

istory

: last measurement saved and historical data.

Summary of Contents for VIBXPERT II

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands