manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT II, Operating Instructions Manual

Share
Download
PRÜFTECHNIK VIBXPERT II Operating Instructions Manual Download Page 44

2-32

VIBXPER

T II 05.2012

Getting started - Data transfer    

Data transfer

The following data is transferred between VIBXPERT and the PC ei-

ther via a direct connection or a network connection:

-  Measurement tasks to VIBXPERT (route)

-  Measurement results to the PC (route, multimode, templates)

-  Machine templates to VIBXPERT

-  Software (update)

-  Printer drivers to VIBXPERT

-   Data backup to the PC

-  Data restore to VIBXPERT

-  PDF and screenshots to the PC
Measurement tasks, results and machine templates are transferred 

using the OMNITREND PC software. All other data are exchanged via 

the 'VIBXPERT utility' tool found on the PRÜFTECHNIK CD and that 

must be installed locally on the PC. Also, PDF files can be saved to a 

USB pen drive, so they can be opened and printed from a PC. 
Exchanging data between the measuring device and a PC requires 

either a direct connection or a network connection.

Direct connection to PC 

-  s

erial

 

connection

: Connect the PC cable VIB 5.430-2 to the digital 

port (yellow) and serial port of the computer.

-  usB 

connection

: Connect the USB cable VIB 5.330SUSB to the com-

munication port (green) and USB port of the computer.

Serial and USB

 

VIB 5.430-2

VIB 5.330SUSB

USB

Serial

-  p

atch

 

connection

: Connect the Ethernet cable VIB 5.331 to the com-

munication port (green) and network card of the computer. 

-  p

atch

 

connection

 

via

 

huB

: Connect the Ethernet cable VIB 5.331 to 

the communication port (green). Connect a standard patch cable 

to the network card of the computer. Connect both cables to a  hub. 

Patch (RJ 45)

Hub

VIB 5.331

Patch cable

VIB 5.331

Summary of Contents for VIBXPERT II

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands