manualshive.com logo in svg

PRÜFTECHNIK VIBXPERT II, Operating Instructions Manual

Share
Download
PRÜFTECHNIK VIBXPERT II Operating Instructions Manual Download Page 34

2-22

VIBXPER

T II 05.2012

Tranducer detection and Hardware settling  

In this menu, the transducer detection feature and the settling of the 

amplifier stages in VIBXPERT can be switched on and off. Additional 

information can be found in the 'Route Setup' section (p. 2-17). 

The settling of the amplifier can only be activated when the trans-

ducer detection is switched off. 
The settings in this menu apply to the 'Multimode' operating mode 

only. The settings for the 'Route' and 'Machine template' modes are 

made in the ‘Route Setup’ menu. 
After the device is switched on, the amplifiers always settle prior to 

the first measurement.

Sensor test  

Here you can manually check the measurement path to the sensor. For 

ICP sensors, use the 'ICP Sensor Test' menu; for all other sensors, use 

the 'Sensor Test' menu.

•  Select the channel to which the sensor is connected (A, B).

•  Click on START. 

  VIBXPERT then checks the measurement path and displays the re-

sult ('LineDrive', 'Open line', 'Short circuit', etc.). 

Default vibration sensor (Multimode)

A default sensor can be specified for all vibration measurements in the 

'Multimode' mode. In the route / machine template, a default sensor 

can only be set up via the 'Runtime setup' menu (p. 3-18) or the Route 

Device Setup (p. 2-17) respectively.
•  Activate the checkbox and select the vibration sensor.

Note

Getting started - Basic settings      

Left:

Checking the measurement  

route on channel B 

Right:

Standard sensor for vibration mea-

surement in 'Multimode'

Summary of Contents for VIBXPERT II

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands