PRÜFTECHNIK VIBXPERT II Operating Instructions Manual Download Page 19

Page: 19 / 176

2-7

VIBXPER

T II 05.2012

Getting started - Power supply

Power supply

VIBXPERT is supplied with energy by a Lithium-Ion rechargeable bat-

tery. With the power on the the battery icon on the display indicates

the residual charge of the battery:



Note

VIBXPERT charger
VIB 5.320 INT

Follow the instructions for connection and disconnection of the

cable in the section ‘Interfaces’ (page 2-5).
The second free channel can in fact be used for measuring, but elec-

trical interference can lead to faulty measurements under certain

circumstances!

Battery icon

Residual charge 100%

Residual charge 25%

Battery is being charged

Battery almost empty

If the battery is almost empty, a message appears on the display and

the blue LED flashes. The battery can be charged either in the device

or in the external charging station (option, VIB 5.324) using the VIBX-

PERT charger (VIB 5.320 INT).

Follow the safety instructions enclosed with the charger.

Charging the battery in the device

Connect the charger to one of the two analog input channels (A / B).

VIBXPERT can be operated during charging.

Attention!

Summary of Contents for VIBXPERT II

















































































































































































Search results

Summary of Contents for VIBXPERT II

Reviews:

Brands by name

Popular brands

PRÜFTECHNIK VIBXPERT II, Operating Instructions Manual

Search results

Summary of Contents for VIBXPERT II

Reviews:

Brands by name

Popular brands