PRONAR T286 Operator'S Manual Download Page 130

Page: 130 / 168

Pronar T286

SECTION 5

5.14

Turn off tractor engine and remove key from ignition.

Immobilise tractor with parking brake.

Make sure that the trailer's brakes are not engaged.

Secure the trailer with wheel chocks.

FIGURE 5.6

Principle of brake system adjustment

(1) brake cylinder piston, (2) brake cylinder membrane, (3) expander arm, (4) adjustment

bolt, (5) cylinder fork, (6) position of fork pin, (7) brake cylinder bracket, (A) mark on the brake

cylinder at brake release position, (B) mark on the brake cylinder at full braking position, (C)

position of arm at brake release position, (D) position of arm at full braking position

Make a line (A) on the brake cylinder piston (1) to indicate the position of the

maximum withdrawal of the brake cylinder piston when the trailer's brakes are

released.

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Related manuals for T286

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Related manuals for T286

Brands by name

Popular brands