PRONAR T286 Operator'S Manual Download Page 71

Page: 71 / 168

SECTION 3

Pronar T286

3.31

3.2.15 ELECTRIC LIGHTING SYSTEM

The trailer's electrical lighting system is designed for 12 V DC supply. In order to cooperate

correctly with the trailer, the tractor should be equipped with a 7-pin electric socket. The

trailer's electrical lighting system should be connected with the tractor using a suitable

connection lead (10) with a 7-pin plug at both ends - figure (3.23).

TABLE 3.3

List of electrical component markings

SYMBOL

FUNCTION

Front socket

Rear socket

OBP1

Right side clearance lamp (LED)

OBL1

Left side clearance lamp (LED)

Front parking light, right side (LED)

Front parking light, left side (LED)

Rear right lamp assembly (LED)

Rear left lamp assembly (LED)

OTP

Right license plate light (LED)

OTL

Left license plate light (LED)

Rear clearance lamp, right side (LED)

Rear clearance lamp, left side (LED)

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands