PRONAR T286 Operator'S Manual Download Page 89

Page: 89 / 168

SECTION 4

Pronar T286

4.15

4.4

HITCHING AND UNHITCHING THE SECOND TRAILER

A second trailer may only be hitched if it is a machine built on a dual axle chassis and if it

fulfils all the requirements specified in section 1.

Hitching the second trailer to the tractor - trailer unit requires experience in driving an

agricultural tractor with a trailer. While hitching the second trailer, it is recommended to use

the help of another person to guide the tractor driver.

Hitching the second trailer

Position the tractor with the first trailer hitched directly in front of the second

trailer's drawbar.

Immobilise the second trailer with parking brake.

FIGURE 4.6

Rear hitch

(1) hitch body, (2) hitch pin, (3) hitch lifting handle

Raise hitch pin (2) of the first trailer using handle (3) - figure (4.6).

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands