PRONAR T286 Operator'S Manual Download Page 32

Page: 32 / 168

Pronar T286

SECTION 2

2.8

FIGURE 2.1

Location of the slow-moving vehicle warning sign

(1) slow-moving vehicle warning sign

•

A load protruding beyond the edge of the trailer should be marked according to

the road traffic regulations. Do NOT transport loads forbidden by the

Manufacturer.

•

Do NOT exceed the trailer's maximum carrying capacity. Exceeding the carrying

capacity may lead to damage to the machine, loss of stability and danger while

driving. The brake system is adjusted to the gross weight of the trailer, exceeding

the weight limit causes drastic reduction of basic braking effectiveness.

•

Prolonged driving across steep ground may lead to loss of braking efficiency.

•

During reversing one should use the assistance of another person. During

manoeuvring the person helping must stay at a safe distance from the danger

zone and be visible all the time to the tractor driver.

•

Do NOT attempt to board trailer while travelling.

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Related manuals for T286

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Related manuals for T286

Brands by name

Popular brands