PRONAR T286 Operator'S Manual Download Page 115

Page: 115 / 168

SECTION 4

Pronar T286

4.41

4.11

HYDRAULIC STEERING SYSTEM OPERATION

In order to ensure proper operation of the hydraulic steering system and safe use of the

trailer, suitable and certified tractor hitches according to ISO 26402:2008 should be used.

During the first hitching of the trailer to the tractor, check correctness of operation of the

wheel steering system. If system operation is found to be incorrect, follow these steps:

Hitch trailer to tractor using drawbar eye and ball control hitch and

then, secure the drawbar,

open two valves (3) located near the hand pump - figure (4.9),

FIGURE 4.9

Hydraulic hand pump

(1) oil tank, (2) hand pump lever, (3) hydraulic valve, (4) pressure gauge, (A) open position,

(B) closed position

drive the tractor with the trailer attached at such a distance as to

position the trailer wheels for forward driving,

fill the system by means of the pump using hand lever (2) until

each pressure gauge (4) indicates pressure of 80 bar,

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Related manuals for T286

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Related manuals for T286

Brands by name

Popular brands