PRONAR T286 Operator'S Manual Download Page 55

Page: 55 / 168

SECTION 3

Pronar T286

3.15

TABLE 3.2

Working modes of the loosening-parking valve

VALVE

OPERATION

MODE

RED PUSH-

BUTTON

BLACK PUSH-

BUTTON

DESCRIPTION

RELEASED

DEPRESSED

RELEASED

The machine is braked with parking
brake.

If the red push-button is released, the
trailer is immobilized with parking brake
regardless of the black push-button
position.

DEPRESSED

RELEASED

Machine is prepared for travel.

Pneumatic conduits are connected to the
trailer. Black push-button can not be
depressed.

Machine is braked

Pneumatic conduits are not connected. If
the black push-button is depressed, the
brake will be released.

DEPRESSED

Parking brake is released, manoeuvre
position.

The trailer's brake is completely released.
Pneumatic conduits are not connected.

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands