PRONAR T286 Operator'S Manual Download Page 129

Page: 129 / 168

SECTION 5

Pronar T286

5.13

FIGURE 5.5

Design of axle brake system

(1) expander arm , (2) expander shaft, (3) adjustment bolt, (4) brake cylinder, (5) brake

cylinder piston, (6) cylinder fork, (7) fork pin

IMPORTANT!

The positions for fixing the brake cylinder in the bracket openings and the brake cylinder
pin in the expander arm are determined by the Manufacturer and must not be changed.

Each time when dismantling the pin or brake cylinder, the original fixing position should
be marked.

The inspection of the brake operation involves measuring the extension length of each brake

cylinder piston while braking at parking. If the brake cylinder piston stroke exceeds the

maximum value (45 mm), the braking system should be adjusted.

Required maintenance activities

Hitch trailer to tractor.

Summary of Contents for T286









































































































































































Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands

PRONAR T286, Operator'S Manual

Search results

Summary of Contents for T286

Reviews:

Brands by name

Popular brands