PRONAR PT512 Operator'S Manual Download Page 79

Page: 79 / 139

CHAPTER 4

Pronar PT512

4.11

Securing the load by means of a canvas cover

When standing on the front platform, start unfolding the cover (2) by means of

a crank (1).

Pass all tensioning straps (4) through clamps (3) located on the trailer's

loading case.

Pull the cover on the right side.

Pull the cover on the front and than on the rear wall of the loading case.

FIGURE 4.3

Canvas cover

(1) slat and a crank, (2) canvas cover, (3) clamp, (4) tensioning strap

4.4.1 GENERAL INFORMATION ON THE LOADING

Before beginning loading, make certain that the loading case walls, extensions and the rear

slide gate are properly closed and secured. The trailer's wheels must be in line with the

tractor's wheels and the trailer must be hitched to the tractor. Loading should only take place

when the trailer is parked on a level surface.

Regardless of the type of load carried, the user is obliged to secure it in such a manner that

the load is unable to move and fall out on the road. If this is impossible, do not transport this

type of load.

Summary of Contents for PT512












































































































































Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands

PRONAR PT512, Operator'S Manual

Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands