PRONAR PT512 Operator'S Manual Download Page 52

Page: 52 / 139

Pronar PT512

CHAPTER 3

3.6

FIGURE 3.2

Loading case – view from the rear

(1) upper frame, (2) side wall, (3) front wall, (4) rear wall, (5) wall rear pillar, (6) lever,

(7) extension rear pillar, (8) hinge, (9) front extension, (10) side extension, (11) rear extension

Access ladders (2) and (3) are attached to the front wall and extension. An additional step

facilitating access to the loading case is bolted to the inside part of the front extension.

Optionally the trailer can be equipped with a foldable canvas cover (5) with its frame. Another

piece of equipment facilitating the canvas cover handling is a platform (4) attached to the

trailer's front wall. The pull-off springs (6) facilitate the side walls opening. The springs (6) and

the platform (4) are available optionally.

Summary of Contents for PT512












































































































































Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands

PRONAR PT512, Operator'S Manual

Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands