PRONAR PT512 Operator'S Manual Download Page 120

Page: 120 / 139

Pronar PT512

CHAPTER 5

5.24

User is obliged to perform only the following maintenance work on the hydraulic system:

•

visual inspection and control of system tightness,

•

inspection of the technical condition of hydraulic connectors.

5.4.2 CONTROL OF HYDRAULIC SYSTEM TIGHTNESS

Scope of maintenance

Hitch the trailer to a tractor.

Connect all hydraulic system lines according to instructions in Operator's

Manual.

Clean connectors and cylinders (tipping cylinder, supports and possible

hydraulic brake cylinders).

Make a test tipping of loading case to the rear and sideways.

Press tractor brake pedal several times.

If the trailer is equipped with hydraulic brake system.

Inspect hydraulic lines and cylinders for tightness.

If oil on hydraulic cylinder body is detected, locate the source of leak. Inspect seals when

cylinder is completely extended. Minimum leaks (symptoms of "sweating") are permissible,

but if leaks in form of "droplets" are detected, stop using machine until fault is removed. If the

fault is related to brake cylinders, stop using the trailer until fault is removed.

Check tightness:

•

after first week of use,

•

every 12 months of use.

5.4.3 CHECKING THE TECHNICAL CONDITION OF HYDRAULIC CONNECTORS

AND SOCKETS

Hydraulic connectors and sockets used for connecting the second trailer must be in good

technical condition and kept clean. Each time before connecting, check if tractor sockets or

connectors of second trailer are in good condition. Tractor and trailer hydraulic systems are

Summary of Contents for PT512












































































































































Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands

PRONAR PT512, Operator'S Manual

Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands