PRONAR PT512 Operator'S Manual Download Page 58

Page: 58 / 139

Pronar PT512

CHAPTER 3

3.12

FIGURE 3.8

A single-line hydraulic braking system

(1) electro-hydraulic valve, (2) hydraulic cylinder, (3) hydraulic quick coupling, (4) hydraulic

accumulator, (5) socket, (6) valve connector cable, (7) information decal

The main hydraulic brake (available optionally) is activated from the tractor driver's cab by

pressing the brake pedal. A tractor with an appropriate hydraulic system is required to

operate the trailer's hydraulic braking system. The function of an electro-hydraulic valve (1) –

figure (3.9) – is to operate the trailer brakes simultaneously with the tractor brakes. Before

driving off, check the brakes operation. To do so, press the brake pedal several times to rise

a pressure in the hydraulic accumulators. The connector cable (6) is used to connect the

trailer's brake valve with a tractor's electrical system. In case of an incidental disconnection of

the cable (6) between the trailer and a tractor, the brake valve will automatically activate the

Summary of Contents for PT512












































































































































Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands

PRONAR PT512, Operator'S Manual

Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands