PRONAR PT512 Operator'S Manual Download Page 54

Page: 54 / 139

Pronar PT512

CHAPTER 3

3.8

FIGURE 3.4

Rear wall slide gate

(1) slide gate, (2) lever, (3) locking bolt

3.2.3 THE MAIN BRAKE

The trailer can be equipped with one of three of main brake types:

•

a single- or twin-line pneumatic braking system with three position manual

regulator – see figure (3.5),

•

twin-line pneumatic braking system with automatic regulator – see figure (3.6),

•

hydraulic braking system – see figure (3.8).

The standard version of the trailer is fitted with a twin-line pneumatic braking system. If there

is a need to install a single-line braking system, this can be carried out by the user. Elements

required to alter the system are delivered as the standard equipment of the trailer.

Detailed information on installation of the single-line braking system can be found in part

5.3.7 – INSTALLATION OF A SINGLE-LINE PNEUMATIC SYSTEM.

Summary of Contents for PT512












































































































































Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands

PRONAR PT512, Operator'S Manual

Search results

Summary of Contents for PT512

Reviews:

Brands by name

Popular brands