Primera CX1000 Operator'S Manual Download Page 5

Page: 5 / 54

Introduction 1

Thank you for purchasing the CX1000 Color Label Printer. The CX1000 Color Label Printer may

also be labeled as the CX1000 Color Label Press or as the Color Label Press in PTPrint software, the

status monitor software or the printer driver. Hereafter in the manual the CX1000 Color Label

Printer will be referred to as the "CX1000". The laser printer portion will be referred to as the

"printer". The unwinder and rewinder unit will be referred to as the "base". Toner and label stock

will be referred to as "media".

This manual is one of many sources of information for this product. If you have problems or

questions please consult one of these resources:

•

Tech Support Phone: 763-475-6979

•

Tech Support Email: www.primera.com/contactsupport

•

Online Knowledgebase: www.primera.com/kb

Important Note on Label Press Operating Environment!

It is strongly recommended that the

CX1000 Color Label Press is operated in an air-conditioned, humidity controlled, smoke free, pet free

environment.

Section 1: Introduction

Rewinder

Label Guide

Rewinder

Dancer

Arm

Cut/Stop Button

Cutter

Label Guide Discs

Unwinder

Printer

Control Panel

Feeder Door

Tension Knob

Figure 1-1.

Unwinder

Dancer

Arm

Eyemark Sensor

Summary of Contents for CX1000























































Search results

Summary of Contents for CX1000

Reviews:

Related manuals for CX1000

Brands by name

Popular brands

Primera CX1000, Operator'S Manual

Search results

Summary of Contents for CX1000

Reviews:

Related manuals for CX1000

Brands by name

Popular brands