Primera CX1000 Operator'S Manual Download Page 46

Page: 46 / 54

42 Maintenance and Troubleshooting

9.5 Stop/Cut Button

Press the Stop/Cut button located on top of the cutter if you need to quickly stop a job. Do not use

this method for non-emergencies since it will deposit a large amount of toner on the ITU that will be

cleaned and placed in the waste toner bin. Repeated use will cause toner build up on the cleaning

mechanism and wear on the ITU belt. For non-emergencies, cancel the job using the control panel

on the printer.

In order to continue printing you will need to cancel the job in the printer’s internal memory.

Follow the prompts on the control panel to cancel the job. The control panel will display "Load MP

Feeder Universal" and ask you to cancel "your file name" or "Continue". Use the arrow button to

scroll through menu and the check button to select "Cancel".

Finally, reset the printer by turning it off and on again using the power switch.

9.6 Error Messages

Rip Software Service 900.

This error can appear on the printer LCD Control Panel panel after the

system is stopped in the middle of job using the Stop/Cut button. Turn off the printer and turn it

back on again to clear the error.

The printer takes a long time to start printing / Engine warming appears on the control panel

(More than 5 minutes).

•

Larger files will take longer to start printing.

•

A slower network will cause a delayed print. Try connecting directly to PC with crossover

cable or reevaluate cabling from computer to CX1000.

•

Change the IP address of the printer or look for any IP address conflicts on the network.

The header(leader) or footer(trailer) is longer than expected.

Change the header/footer length via

the Option tab/button in the Status Monitor. The minimum footer in all cases is 3 feet. This can not

be made shorter.

Figure 9-1.

Stop

Press to

Cut

Stop/Cut Button

Summary of Contents for CX1000























































Search results

Summary of Contents for CX1000

Reviews:

Related manuals for CX1000

Brands by name

Popular brands

Primera CX1000, Operator'S Manual

Search results

Summary of Contents for CX1000

Reviews:

Related manuals for CX1000

Brands by name

Popular brands