Primera CX1000 Operator'S Manual Download Page 10 | Manualshive

Page: 10 / 54

background image

6 Unpack and Assemble

9. Locate the rewinder stand. Attach it to the right side of the printer base. Align the hooks on the

rewinder stand to the slots on the printer stand.

10. Locate the rewinder. The rewinder has a longer dancer arm and no 6-pin ports on the back.

Attach it to the stand using the #2 Phillips screws and the washers found in the hardware bag.

Use the locator pegs on the stand and align them with the holes on the bottom of the rewinder.

Figure 2-9.

Locator Pegs

Figure 2-8.

«
...
8
9
10
11
12
...
»

Summary of Contents for CX1000























































Reviews:

No comments

Related manuals for CX1000

Brand: Barista Mate Pages: 12

Brand: Gaggia Pages: 7

Brand: Ice-O-Matic Pages: 2

Brand: Ice-O-Matic Pages: 25

Hotel Dispenser CD 40030 Series

Brand: Ice-O-Matic Pages: 2

Brand: Canon Pages: 285

Brand: Ice-O-Matic Pages: 2

Brand: Marco Pages: 9

Brand: nedis Pages: 44

Brand: OK. Pages: 63

Brand: U-Line Pages: 44

Brand: Kalorik Pages: 20

Brand: Farberware Pages: 12

Brand: Weber Pages: 56

Brand: SEVERIN Pages: 72

Brand: U-Line Pages: 36

Accents 162005EE

Brand: Morphy Richards Pages: 40

Brand: Exido Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands