manualshive.com logo in svg

Praxair 1264, Operator'S Manual

Share
Download
Praxair 1264 Operator'S Manual Download Page 30

 

Model 1264 Powder Feeder 

 

 

Operator’s Manual

 

_____________________________________________________________________________________________________________________

 

 

1.6.3 

Cobalt, Chromium, and Tellurium 

The principal hazard when spraying or blasting these materials comes 
from ingestion, inhalation, and the subsequent absorption of fumes, dust, 
or vapors.   
 
The fumes and dust from chromium alloys (such as stainless steels, nickel 
chromium, and chromium oxide) and tellurium are  toxic and hazardous.  
Provide respiratory protection and adequate ventilation wherever the fume 
and dust concentration is above the threshold limit (see "Threshold Limit 
Valves" in section 1.6.6). 

1.6.4 

Tin and Zinc 

Usually encountered in the forms of their oxides and not considered toxic, 
tin and zinc may cause violent illness, including coughing, headache and, 
particularly in the case of zinc oxide fumes, nausea, vomiting, chills, 
fever, muscle and joint pain, and marked thirst.  (In the case of zinc oxide, 
the effect has been known as "brass founder's ague," "brass chills," "zinc 
fever," or "metal fume fever.")  Temporary short term immunity can be 
developed. 
 
Prevention consists of adequate ventilation and proper respirators (see 
"Respiratory Protection" in section 1.5.2 and "Confined Spaces" in section 
1.5.5).  Preclude from the work any operators with pulmonary disease or 
those who continue to suffer discomfort even with proper ventilation and 
respirator measures.

 

1.6.5 

Solvents 

The radiation generated  by plasma or arc spraying causes rapid 
decomposition of some solvent vapors into noxious and toxic gases, even 
at considerable distance from the arc.  Slow extraction of the part from the 
solvent cleaning tank can reduce this problem.  When spraying vapor-
degreased parts, take extra care to see that all solvent (vapors or liquid 
films or drops of solvent caught by pockets and crevices) is removed prior 
to thermal spraying. 
 
The ultraviolet radiation from plasma and arc spraying generates airborne 
ozone.  The amount of ozone produced may exceed the maximum 
allowable concentration in confined spaces.  Excess ozone production 
should be avoided. 

Issued: 10/11 

 

Page 

19

  

 

Summary of Contents for 1264


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands