background image

30

31

WARNING

:

 Depending on the installation, this anti-crushing system 

is not enough to comply with EN13241, EN12978 and EN12453, and to 

avoid accidents with people and animals, requiring the use of photocells 

and safety edges.

Even using the inherent anti-crushing system, it is recommended to use 

passive edges for better performance and protection.

ENCODER OPERATION TEST

It is possible to test the encoder of the operator by connecting it to the board and 

checking if the “ENC” LED is flashing when the operator is moved.

EVENTS AND FAILURES INDICATIONS

Microcontroller operation indication

The main function of the “OSC” LED is to indicate that the controller board is operating. 

It flashes with a fixed frequency of ~ 1 Hz, since the power is turned on.

Motor over current or short circuit

The “OSC” LED flashes rapidly (in a 0.1- second interval) to warn that the power 

stage has tripped due to overcurrent or short circuit in the motor. The board may 

operate normally after 10s of the occurrence of the overload.

Overheating

The “END” LED flashes rapidly,  in a 0.1-second interval, to warn that the power stage 
has tripped due to overheating of the heatsink of the environment. The operator can 
only be operated again if the temperature decreases to less than 100ºC.

EEPROM fault

The “OSC” LED flashes twice when Memory is not present.

EEPROM with invalid data

The “OSC” LED flashes three times when Memory is present but it has a content that 
the microcontroller does not identify as a Valid Transmitter Code.

MAINTENANCE ANd TROUbLESHOOTING

 

In the table below are found some PROBLEMS - DEFECTS, PROBABLE CAUSES AND 

CORRECTIONS - which may occur in the operator. Before any maintenance, it is 

necessary to completely disconnect the power grid.

Open limit switch

The “END” LED flashes when the gate reaches an open limit switch.

Closed limit switch

The “END” LED is lit when the gate reaches a closed limit switch.

Load in the capacitors

The “BUS” LED indicates that there is load on the power stage capacitors.

WARNING: 

The power region (capacitor region) of the board 

must not be touched while this LED is lit even after the inverter is 

disconnected from the electricity grid!

Command

The “CMD” LED on indicates that the control panel is receiving some command 

from the digital inputs, such as OPE, CLO, PBU, SFO or SFC.

DEFECTS

PROBABLE CAUSES

CORRECTIONS

Motor does not start / 

does not move

A) Power grid off

A) Make sure the power grid 

is turned on correctly

B) Open/ Burned 

fuse

B) Replace fuse with the same 

specification

C) Locked gate

C) Make sure that there are 

no objects blocking the gate 

operation

D) Limit switch with 

defect.

D) Replace the limit switch 

system (analog and / or 

digital)

Summary of Contents for DZ 2.0





















Reviews: