manualshive.com logo in svg

Poldent Endostar Provider, Instructions For Use Manual, Page: 4 / 48

Share
Download
Poldent Endostar Provider Instructions For Use Manual Download Page 4

3

Instructions for Use  2019-03-20

The warning symbols (

) and caution symbols (

) that appear next to the main text on the right hand side of the page refer to and are ex-

plained by the Warnings and Cautions at the bottom of the page.

Accident Prevention

Make sure to obtain clear instructions concerning the various ways to use the device described in this accompanying manual.

Most operation and maintenance problems result from insufficient attention to basic safety precautions and not being able to foresee potential 
accidents.
Problems and accidents are best avoided by anticipating potential dangers and operating the device in accordance with the manufacturer’s rec-
ommendations. First, thoroughly read all precautions and instructions pertaining to safety and accident prevention. Then operate the device with 
the utmost caution to prevent either damaging the device itself or causing bodily injury.

The following symbols and expressions indicate the degree of danger and harm that could result from ignoring the corresponding instructions:

This alerts the user of important points concerning operation or the risk of equipment damage.

The user (e.g., healthcare facility, clinic, hospital etc.) is responsible for the management, maintenance, and use of medical devices.

This equipment must only be used by dentists and other legally licensed professionals.
Do not use the Endostar Provider for anything other than its specified dental purpose.

This alerts the user of the possibility of extremely serious injury or complete destruction of the device, as well as other property dam-
age including the possibility of fire.

This alerts the user of the possibility of minor or moderate injury or damage to the device.

Customers

Preventing Accidents

Summary of Contents for Endostar Provider

















































Reviews:

No comments