manualshive.com logo in svg

Poldent Endostar Provider, Instructions For Use Manual, Page: 29 / 48

Share
Download
Poldent Endostar Provider Instructions For Use Manual Download Page 29

28

Instructions for Use  2019-03-20

•  Do not use any type of spray other than the LS OIL.
•  Failure to lubricate the contra angle will result in a malfunction.
•  Put the cap on after use. Oil could seep out if the container is tipped over or the nozzle points down.
•  After lubricating, wipe oil from the outside of the nozzle. Otherwise oil may seep out from under the cap.
•  Leave the contra angle in the paper cup for at least 10 minutes so that the oil is thoroughly absorbed by the contra angle mechanism.

Autoclavable Components

Do not use anything except ethanol (70 vol% to 80 vol%) for cleaning. 

Never wipe the contra angle with solutions containing formalin cresol (FC) 

or sodium hypochlorite, which damage plastic; wipe them off immediately if 

they accidentally get on the contra angle.
Do not immerse in any fluid.
Do not connect the contra angle to the motor handpiece immediately after 

lubrication for use or charging. Otherwise the oil seep inside the motor 

handpiece and it might malfunction.

* Only the contra angle needs to be lubricated.

Lubrication

Before autoclaving, the contra angle must be lubricated with the LS OIL.

1 Drop

1 Drop 

Gear

1.  Place the contra angle in a paper cup with the connection end fac-

ing up.

2. Put 5 drops of the LS OIL on the gear and wait for 10 minutes.

3. Put a drop of the LS OIL in each of the two points between the 

built-in electrode and the head as indicated by the arrows in the 
illustration.

4. Take the contra angle out of the paper cup and wipe off any excess 

oil which may have seeped out. Dampen a piece of gauze with 
ethanol (70 vol% to 80 vol%), wring it out and then wipe the con-
tra angle with it.

Summary of Contents for Endostar Provider

















































Reviews:

No comments