Polaris 502 Installation Manual Download Page 43

Page: 43 / 44

LIST OF ACCESSORIES

Solar Powered Battery Charger (10-Watt: RSP10; 20-Watt: RSP20)

The solar panel charges the 12 volt battery when AC power is not available.

One-Button Transmitter. The transmitter works as an input device allowing the user to open or close the

gate from a remote location. It has a range up to 300 feet.

Two-Button Transmitter. The two-button transmitter provides the capability to remotely operate two

separate devices such as two gates, or a gate and a garage door opener. It has a range up to 300 feet.

Mini-transmitter. The mini-transmitter fits on a keychain and allows the user to open or close the gate from

a remote location. It has a range up to 300 feet.

Keypad. The keypad allows for entry by authorized guests informed of the pre-set code. Entering the correct

code causes the gate to open or close. The access code can be easily modified.

Pin Lock. The pin lock replaces the clevis pin when mounting the gate operator to the brackets. It helps to

prevent theft of the gate operator from the gate, while allowing quick release of the operator.

In-Ground Vehicle Sensor. The vehicle sensor is buried near the gate and senses a vehicle that passes within

its 12-foot range. Once detected, the gate opens automatically.

Solenoid Gate Lock. The automatic gate lock provides an additional level of security for the property. When

the gate swings shut, the gate lock closes, securing the gate in the closed position. The gate lock is powered

from the control box of the gate operator. The locking mechanism is a mechanical latch.

Magnetic Gate Lock. The automatic gate lock provides an additional level of security for the property. When

the gate swings shut, the gate lock closes, securing the gate in the closed position. The gate lock is powered

from an external AC power source. The locking mechanism is magnetic.

Push-to-Open Bracket. This bracket is necessary for push-to-open installations.

Replacement Battery. Standard 12 volt, 7.2 amp-hour, maintenance free battery.

LIST OF ACCESSORIES

Summary of Contents for 502













































Search results

Summary of Contents for 502

Reviews:

Related manuals for 502

Brands by name

Popular brands

Polaris 502, Installation Manual

Search results

Summary of Contents for 502

Reviews:

Related manuals for 502

Brands by name

Popular brands