Polaris 502 Installation Manual Download Page 19 | Manualshive

Page: 19 / 44

background image

19

Step 3
The transformer provided is for dry location use only. If used

in an outside outlet, the transformer must be enclosed or

covered for weather protection. Attach AC power wire to the

transformer.

NOTE: DO NOT PLUG TRANSFORMER INTO AC POWER

UNTIL ALL WIRING IS COMPLETED.

Step 4
Install the battery by placing the battery into the control

box. The control box can accommodate one or two batteries.

Warning:

Do not attempt to splice operator wires for

the purpose of extending your wiring connections. Doing

so can void your warranty. Contact technical support for

recommended procedure. 1-800-234-3952.

Figure 22

Figure 21

Battery

Second battery (not included)

Black (-) terminal wire

Red (+) terminal wire

Step 5
Connect the battery terminal wires

to the battery.

Step 6
Plug in transformer. Turn control

box power switch to the ON

position.

WIRING OPERATOR

«
...
17
18
19
20
21
...
»

Summary of Contents for 502













































Reviews:

No comments

Related manuals for 502

TORQUEMASTER 6100

Brand: Wayne-Dalton Pages: 36

Brand: Wayne-Dalton Pages: 24

Brand: Salton Pages: 21

Brand: Gator Pages: 26

Brand: Viking Pages: 44

Brand: RAMSET Pages: 28

Brand: NAS Pages: 19

Brand: Nice Pages: 28

76380 - Classic Chrome Heavyweight Can...

Brand: Hamilton Beach Pages: 5

Brand: Key Automation Pages: 16

Brand: Elite Pages: 40

Brand: Iijima Pages: 4

Brand: Beninca Pages: 16

Brand: Calimet Pages: 24

Brand: jcm-tech Pages: 8

Brand: Wayne-Dalton Pages: 46

Brand: tousek Pages: 36

Brand: Wayne-Dalton Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands