PLAYSTAR Play Action Climbing Bar Kit Safety Manual & Assembly Instructions Download Page 21

Page: 21 / 32

2" x 4" x

³⁄₄

2" x 4" x 62

¹⁄₂

Remove this board.

LEGEND - Back view

Attach Corner Brackets here.

Attach Corner Brackets

Position brackets so that the short sides are against the 2" x 4" x
62

¹⁄₂

" board as shown.

Use the brackets as a drill guide and drill

¹₈

" holes 1" deep into the

boards. Attach with #8 x 1

¹₄

" deck screws.

Use the brackets as a drill guide and drill

¹₄

" holes 2

¹⁄₂

" deep

through the

long

side and a

³⁄₈

" hole completely through the

short

side of the bracket. Secure the

long

side with

³⁄₈

" x 3" lag screw and

³⁄₈

" washer. Secure the

short

side with

³⁄₈

" x 2" hext bolt,

³⁄₈

" washer

and

³⁄₈

" lock nut.

Items for this STEP:

(2) Corner Brackets
(8) #8 x 1

¹⁄₄

" deck screws

(2)

³⁄₈

" x 2" hex bolts

(2)

³⁄₈

" x 3" lag screws

(2)

³⁄₈

" lock nuts

(4)

³⁄₈

" washers

LT 6456 Climbing Bar Instructions_AS Instructions '04 R1 2/24/10 3:04 PM Page 21

Summary of Contents for Play Action Climbing Bar Kit

































Search results

Summary of Contents for Play Action Climbing Bar Kit

Reviews:

Related manuals for Play Action Climbing Bar Kit

Brands by name

Popular brands

PLAYSTAR Play Action Climbing Bar Kit, Safety Manual & Assembly Instructions

Search results

Summary of Contents for Play Action Climbing Bar Kit

Reviews:

Related manuals for Play Action Climbing Bar Kit

Brands by name

Popular brands