PLAYSTAR Play Action Climbing Bar Kit Safety Manual & Assembly Instructions Download Page 20 | Manualshive

Page: 20 / 32

background image

88”

Items for this STEP:

(4) #8 x 1

¹⁄₄

" deck screws

(2)

³⁄₈

" x 2" hex bolts

(2)

³⁄₈

" lock nuts

(2)

³⁄₈

" washers

LEGEND

Remove slide.
Remove existing climbing bars from tower.
Remove 2" x 4" x 38

³⁄₄

" board (see next page).

Reattach slide to tower opening where climbing bars were attached.
Follow instructions provided with your slide to attach to tower.

20

Go to page 31 for
anchoring instructions.

Dig into the ground 10

¹⁄₂

"

at the base so the top bars
are leveled.

Attach Climbing Bar Assembly

Lift Climbing Bar Assembly into an upright position at the
dimension shown, making sure it is centered in the opening.

Dig into the ground 10

¹⁄₂

" at the base so the top bars are leveled.

Use the brackets as a drill guide and drill

¹₈

" holes 1" deep into

the boards. Attach with #8 x 1

¹₄

" deck screws.

Drill a

³⁄₈

" hole completely through the boards. Secure with

³⁄₈

" x

2" hex bolt,

³⁄₈

" washer and

³⁄₈

" lock nut.

Go to page 29 for instructions to reattach Climbing Bars.

LT 6456 Climbing Bar Instructions_AS Instructions '04 R1 2/24/10 3:04 PM Page 20

«
...
18
19
20
21
22
...
»

Summary of Contents for Play Action Climbing Bar Kit

































Reviews:

No comments

Related manuals for Play Action Climbing Bar Kit

Brand: Landoll Pages: 6

Brand: MacDon Pages: 45

Brand: H&S Pages: 30

Brand: KAM Pages: 5

Advisor Guide Pedestrian Signal

Brand: Campbell Pages: 14

Brand: Backyard Discovery Pages: 10

Easypack coiler-lite

Brand: Pregis Pages: 16

Brillion Zone Commander 2511

Brand: Landoll Pages: 48

Brand: BEBE CONFORT Pages: 13

Brand: HUBBELL LIGHTING Pages: 2

B1542A Pulsed IV Package

Brand: Keysight Technologies Pages: 160

Brand: DUI Pages: 5

MAXIBLOC AN10006T

Brand: Deltaplus Pages: 64

Brand: platypus Pages: 10

Brand: ADJ Pages: 20

Brand: EIDER Pages: 48

Brand: Karma Pages: 12

Brand: NJD Electronics Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands