PLAYSTAR Play Action Climbing Bar Kit Safety Manual & Assembly Instructions Download Page 17

Page: 17 / 32

Attach Climbing Bar Assembly

Lift Climbing Bar Assembly into an upright position at the dimension shown
making sure it is centered in the opening.

Dig into the ground about

" at the base so the top bars are leveled.

Use the brackets as a drill guide and drill

¹₈

" holes 1" deep into the boards.

Attach with #8 x 1

¹₄

" deck screws.

Drill a

³⁄₈

" hole completely through the board. Secure with

³⁄₈

" x 2" hex bolt,

³⁄₈

washer and

³⁄₈

" lock nut.

Go to page 31 for
anchoring instructions.

¹⁄₂

”

2" x 4"

¹⁄₂

Items for this STEP:

(1) 2" x 4" x 21

¹⁄₂

" board

(4) #8 x 2

¹⁄₂

" deck screws

(4) #8 x 1

¹⁄₄

" deck screws

(2)

³⁄₈

" x 2" hex bolts

(2)

³⁄₈

" washers

(2)

³⁄₈

" lock nuts

Reattach Wood Rock Wall

Cut ten (10)

⁵⁄₄

" x 6" x 28" boards removed from Wood Rock Wall down to

¹⁄₂

Position first

⁵⁄₄

" x 6" x 24

¹⁄₂

" board tight against the ground as shown.

Secure with #8 x 2

¹⁄₂

" deck screws reused from Wood Rock Wall.

Position next

⁵⁄₄

" x 6" x 24

¹⁄₂

" board tight against the first board. Secure

with #8 x 2

¹⁄₂

" deck screws reused from Wood Rock Wall.

Repeat for remaining eight (8) boards, for a total of ten (10)

⁵⁄₄

" x 6" x

¹⁄₂

" boards.

Position 2" x 4" x 21

¹⁄₂

" board flush with top

⁵⁄₄

" x 6" x 24

¹⁄₂

" board as

shown. Secure with #8 x 2

¹⁄₂

" deck screws provided.

Dig into the ground 6" at
the base so the top bars
are leveled.

Ground

LT 6456 Climbing Bar Instructions_AS Instructions '04 R1 2/24/10 3:04 PM Page 17

Summary of Contents for Play Action Climbing Bar Kit

































Search results

Summary of Contents for Play Action Climbing Bar Kit

Reviews:

Related manuals for Play Action Climbing Bar Kit

Brands by name

Popular brands

PLAYSTAR Play Action Climbing Bar Kit, Safety Manual & Assembly Instructions

Search results

Summary of Contents for Play Action Climbing Bar Kit

Reviews:

Related manuals for Play Action Climbing Bar Kit

Brands by name

Popular brands