Planika GaLiO Corten Installation And User Manual Download | Manualshive

Page: 5 / 41

background image

Copyright Planika Sp. z o.o.

www.planikafires.com

IG0033#08

2020-03-20

5

INSTALLATION NOTICE

•

The installation of this appliance is only to be carried out by an authorized person in accordance with the
Manufacturer’s Instructions, local gas fitting regulations, AS/NZS5601.1 installation code for gas burning
appliances and any other relevant statutory regulations.

•

In all cases the installation of this appliance shall meet the requirements as set out in AS/NZS5601.1

IMPORTANT SAFETY NOTICES

•

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

•

DO NOT USE OR STORE FLAMMABLE MATERIAL NEAR THE APPLIANCE.

•

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILST IT IS IN OPERATION.

•

DO NOT MODIFY THIS APPLIANCE.

•

THIS APPLIANCE IS DESIGNED TO OPERATE WITH LUMINOUS FLAMES. THIS MAY EXHIBIT SLIGHT CARBON

DEPOSITS. THIS IS A NORMAL CONDITION AND IS NOT COVERED BY WARRANTY

•

THE GUARD IS FITTED TO THIS APPLIANCE TO REDUCE THE RISK OF FIRE OR INJURY FROM BURNS AND NO

PART OF IT SHOULD BE PERMANENTLY REMOVED. FOR PROTECTION OF YOUNG CHILDREN OR THE INFIRM,
A SECONDARY GUARD IS REQUIRED.

WARNING

This fireplace has a naked flame, care should be taken when it is operating if children or the infirm are in close
proximity. A safety screen is recommended if constant supervision is not possible. It is recommended that a secondary
guard complying with AS-NZS2286 be installed.

The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not
play with the appliance.

«
...
3
4
5
6
7
...
»

Summary of Contents for GaLiO Corten










































Reviews:

No comments

Related manuals for GaLiO Corten

Signature 0346217

Brand: Mimosa Pages: 12

Brand: Napoleon Pages: 17

Brand: Desa Pages: 36

Brand: Bio Fireplace Group Pages: 4

Brand: Travis Industries Pages: 26

Brand: Napoleon Pages: 8

Luna Gold Series

Brand: M Design Pages: 14

Brand: Trimline Pages: 22

Brand: PFS Pages: 24

Brand: Vermont Castings Pages: 48

Brand: Lennox Hearth Products Pages: 24

Brand: Williams Pages: 2

New York Corner

Brand: Nordpeis Pages: 20

Brand: Royal Pages: 33

Brand: Royal Pages: 56

Brand: Pioneer Pages: 16

OPTIMYST ENGDL20

Brand: EWT Pages: 65

Brand: Whalen Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands