background image

Copyright Planika Sp. z o.o.  

www.planikafires.com 

 

IG0033#08 

2020-03-20 

 

26 

4.4.12.

 

Automatic Turn Down To Pilot 

 

3 Hour No Communication Function 

The valve will turn to pilot flame if there is no communication between handset and receiver for a 3 hour period. The 
fire will continue to function normally when communication is restored.  
 

Receiver Overheating

 

 

Powered by mains adapter: The valve turns to pilot flame if the  receiver temperature is higher than 176 °F 

(80 °C). If batteries are installed in the receiver in this configuration the temperature must not exceed 60 °C. 

 

Powered by batteries and/or connected to the V module: The valve turns to pilot position if the temperature 
in the receiver is higher than 140 °F (60 °C). 

 

NOTE:

 When the receiver temperature is below 140 °F (60 °C), the main burner can be turned ON manually. 

 
 
 

4.4.13.

 

Automatic Shut Off 

Countdown Timer 

At end of countdown time period, the fire shuts off. The Countdown Timer only works in Manual, Thermostatic, and 
Eco Modes. Maximum countdown time is 9 hours and 50 minutes.  

 
Low Battery Receiver 

With low battery power in the receiver the system shuts off the fire completely. This will not happen if the power 
supply is interrupted.  
 

On-Demand Pilot 

 

This green feature eliminates gas energy consumption during extended appliance inactivity. When the appliance 
is inactive for an extended period of time the system automatically extinguishes the pilot. This feature helps the 
consumer realize cost benefits by automatically eliminating energy consumption during non-heating months and 
limited use.  

 

The programmed length of inactivity to activate the system is specified by the appliance manufacturer and cannot 
be altered in the field. 

 

 
 
 

Summary of Contents for GaLiO Corten










































Reviews: