Pit Boss 10989, Manual

Page: 15 / 59

WWW.PITBOSS-GRILLS.COM 15 PIT BOSS® GRILLS
ENGLISH
GRILL CARE CHEAT SHEET
ITEM CLEANING FREQUENCY CLEANING METHOD
Bottom of Main Grill Every 5-6 Grill Sessions Scoop Out, Wet/Dry Vacuum Out Excess Debris
Burn Pot Every 2-3 Grill Sessions Scoop Out, Wet/Dry Vacuum Out Excess Debris
Cooking Grates After Each Grill Session Burn Off Excess, Brass Wire Brush
Flame Broiler™ Every 5-6 Grill Sessions Scrape Main Plate with Slider, Do Not Wash Clean
Shelves After Each Grill Session Cloth & Soapy Water
Grease Bucket After Each Grill Session Cloth & Soapy Water
Auger Feed System When Pellet Bag is Empty Allow Auger to Push Out Sawdust, Leaving
Hopper Empty
Hopper Electric Components Once A Year Dust Out Interior, Wipe Fan Blades with Soapy
Water
Air Intake Vent Every 5-6 Grill Sessions Dust, Cloth & Soapy Water
Grill Probe (Sensor) and Shield Every 2-3 Grill Sessions Cloth & Soapy Water
Hopper Assembly
• The hopper includes a pellet clean-out feature to allow for easy
cleaning and the ability to change out wood pellet fuel flavors.
To empty, locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock. Place a
clean, empty pail under the clean-out door and pull the door han-
dle to open the drop-chute access plate, allowing the pellets from
the hopper to empty. Once empty, lift the door handle again to
unlock. Push the drop-chute access plate back into place. Push the
door handle down to lock closed. (G)
NOTE: Use a long handled brush or shop-vac to remove ex-
cess pellets, sawdust, and debris for a complete clean-out
through the hopper screen.
• Running all pellets out of your auger system is recommended if
your grill will be unused for an extended period of time. This can
be done by simply running your grill, on an empty hopper, until all
pellets have emptied from the auger tube.
• Check and clean off any debris from the fan air intake vent, found
on the bottom of the hopper. Once the access panel has been re-
moved, carefully wipe off any grease build-up directly on the fan
blades. Use warm soapy water to cut the soot and grease. This
ensures airflow is clean and sufficient to the feed system. (H)
PELLET CLEAN-OUT FEATURE
The hopper includes a pellet clean-out feature to allow for
easy cleaning and the ability to change out wood pellet fuel
flavors. To empty, follow these steps:
1. Locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock.
2. Place a clean, empty pail under the clean-out door and
pull the door handle to open the drop-chute access plate,
allowing the pellets from the hopper to empty.
NOTE: Use a long handled brush or shop-vac to remove
excess pellets, sawdust, and debris for a complete cleanout through the hopper screen.
3. Once empty, lift the door handle again to unlock. Push
the drop-chute access plate back into place.
4. Push the door handle down to lock closed.
STEP 14
PELLET CLEAN-OUT FEATURE
The hopper includes a pellet clean-out feature to allow for
easy cleaning and the ability to change out wood pellet fuel
flavors. To empty, follow these steps:
1. Locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock.
2. Place a clean, empty pail under the clean-out door and
pull the door handle to open the drop-chute access plate,
allowing the pellets from the hopper to empty.
NOTE: Use a long handled brush or shop-vac to remove
excess pellets, sawdust, and debris for a complete cleanout through the hopper screen.
3. Once empty, lift the door handle again to unlock. Push
the drop-chute access plate back into place.
4. Push the door handle down to lock closed.
STEP 14
PELLET CLEAN-OUT FEATURE
The hopper includes a pellet clean-out feature to allow for
easy cleaning and the ability to change out wood pellet fuel
flavors. To empty, follow these steps:
1. Locate the pellet clean-out door and door handle on the
back side of the hopper. Lift the door handle to unlock.
2. Place a clean, empty pail under the clean-out door and
pull the door handle to open the drop-chute access plate,
allowing the pellets from the hopper to empty.
NOTE: Use a long handled brush or shop-vac to remove
excess pellets, sawdust, and debris for a complete cleanout through the hopper screen.
3. Once empty, lift the door handle again to unlock. Push
the drop-chute access plate back into place.
4. Push the door handle down to lock closed.
STEP 14
G
Snapshot this chart
for reference.
H