53
p
When the screen changes to full-screen rear view camera
image during normal driving, switch to the opposite setting
in “
Reverse Gear Setting.
”.
p
If you touch
while the camera image is displayed, the
displayed image will turn off temporarily.
Setting rear view camera activation
The default setting is “
Off
”.
1 Display the “
System
” setting screen.
Refer to
Displaying the “
System
” setting screen
on page
2 Touch [
Camera settings
].
3 Touch [
Back Camera Input
] to switch “
On
” or
“
Off
”.
Setting the polarity of the rear view
camera
The default setting is “
Battery
”.
1 Display the “
System
” setting screen.
Refer to
Displaying the “
System
” setting screen
on page
2 Touch [
Camera settings
].
3 Touch [
Reverse Gear Setting.
].
Battery
:
The polarity of the connected lead is positive.
Ground
:
The polarity of the connected lead is negative.
Setting the reversed image display
for the rear view image
You can set whether to reverse the rear view camera images to
be displayed on the front screen.
The default setting is “
Off
”.
p
This setting is available only when you stop your vehicle in a
safe place and apply the handbrake.
p
This function is available when “
Back Camera Input
” is set
to “
On
”.
Refer to
Setting rear view camera activation
on page 53
1 Display the “
System
” setting screen.
Refer to
Displaying the “
System
” setting screen
on page
2 Touch [
Camera settings
].
3 Touch [
Back Camera: Reverse Video
] to switch
“
On
” or “
Off
”.
Setting the parking assist guidelines
Displaying the parking assist
guidelines
You can set whether to display the parking assist guidelines on
the rear view camera images when backing up your vehicle.
The default setting is “
Off
”.
1 Display the “
System
” setting screen.
Refer to
Displaying the “
System
” setting screen
on page
2 Touch [
Camera settings
].
3 Touch [
Parking Assist Guide
] to switch “
On
” or
“
Off
”.
Adjusting the parking assist
guidelines
CAUTION
When adjusting the guidelines, be sure to park the vehicle
in a safe place and apply the handbrake.
Before getting out of the car to place the markings, be sure
to turn the ignition switch off (ACC OFF).
The range projected by the rear view camera is limited.
Also, the vehicle width and distance guidelines displayed
on the rear view camera image may differ from the actual
vehicle width and distance. (The guidelines are straight
lines.)
The image quality may deteriorate depending on the usage
environment, such as at night or in dark surroundings.
1 Park your vehicle in a safe place and apply the
handbrake.
2 Using packing tape or similar, place markings
as follows.
Rear bumper
25 cm
25 cm
50 cm
2 m
Markings
Markings
3 Display the “
System
” setting screen.
Refer to
Displaying the “
System
” setting screen
on page
4 Touch [
Camera settings
].
5 Touch [
Parking Assist Guide Adjust
].
6 Set the guidelines by dragging the four points.
Adjust the guidelines so that the guidelines can be overlaid to
the markings
p
Touch / / / /
/
to adjust the guidelines if
necessary. Touch [
Default
] to reset the settings.
Setting the camera for Camera
View mode
To display Camera View at all times, “
Camera View
” needs to be
set to “
On
”. (The same mode is turned on when
is touched
on the camera view screen. The setting value is synchronized.)
The default setting is “
Off
”.
p
To set the rear view camera as the camera for Camera View
mode, set “
Back Camera Input
” to “
On
”.
Refer to
Setting rear view camera activation
on page 53
1 Display the “
System
” setting screen.
Refer to
Displaying the “
System
” setting screen
on page
2 Touch [
Camera settings
].
3 Touch [
Camera View
] to switch “
On
” or “
Off
”.
p
You can also turn this function on by touching [
Camera
View
] on the AV source selection screen or in the source
list.
< CRB4880-A >
System settings