background image

Instruction & Maintenance Manual

Sheet 1.23

Phoenix

 ‘SPC10e’

 Self Propelled Metering Chipping Spreader

03/12

1.2.1

 

Operator’s Position -

Layout of Controls & Instruments

Always enter the Operator’s (Driver’s) position by climbing the
access steps to the front on either side. Normally enter the
machine from the LH side as the armrest and joystick obstructs
access for the RH side.

A second seat allows for an additional person to be carried.
However, there are no operating functions for this person. Any
person in this seat must not distract the operator.

HAZARD WARNING

DO NOT CARRY other persons, other than where the
seat is provided.

DO NOT ALLOW any person to climb onto or off the
machine whilst it is moving, including use of the
normal access steps.

AT NO TIME leave the operator’s position with the
machine still moving. ALWAYS place drive control to
neutral and apply the parking brakes.

ALWAYS ENTER & EXIT the operator’s position via the
access steps unless in an emergency you are unable
to do so.

Once seated in the main operator’s position, the controls
necessary to operate the machine are grouped around the seat.

Seat and Front Steering Column
The operators seat is fitted with a self contained air suspension
to protect the operator from the immediate vibration of the
machine’s motion. The seat is adjustable for height,
forward/rearward position, back rake and posture.

The front steering column and console is adjustable for angle so
that it can be moved towards the seat or towards the
windscreen. A locking screw on the LH side under the main
console slackens the column to allow adjustment.

Summary of Contents for SPC10e































Reviews: