Philips 22PFK4000, User Manual

Page: 22 / 59

3. To start the channel list upload, press

and
select Setup and press OK .
4. Select TV settings > General settings > Copy
channel list > Copy to TV and press OK . You might
be asked to enter the Child lock code of this TV.
5. The TV notifies you if the channel list is copied to
the TV successfully. Unplug the USB memory device.
To an already installed TV
1. Verify the country setting of the TV. (To verify this
setting, press

and select Setup and press OK .
Select Search for channels > Reinstall channels and
press OK . Press

and later Cancel to leave the
Search for channels.)
If the country is correct continue with step 2.
If the country is not correct, you need to start a
reinstallation. To start the reinstallation, press

and
select Setup and press OK . Select TV settings >
General settings > Re-install TV > OK . Select the
correct country and skip the Search for channels.
Finish the installation. When done, continue with step
2.
2. Plug in the USB memory device that holds the
channel list of the other TV.
3. To start the channel list upload, press

and
select Setup and press OK .
4. Select TV settings > General settings > Copy
channel list > Copy to TV and press OK . You might
be asked to enter the Child lock code of this TV.
5. The TV notifies you if the channel list is copied to
the TV successfully. Unplug the USB memory device.
DVB-T or DVB-C
DVB-T or DVB-C reception
If both DVB-T and DVB-C reception is available in
your country and if this TV is ready to receive DVB-T
and DVB-C for your country, you have selected one
or the other during the channel installation.
If you want to change the DVB setting to start a new
channel installation . . .
1. Press

and select Setup and press OK .
2. Select Channel settings and press OK .
3. Select Channel installation > Antenna connection >
Antenna (DVB-T) or Cable (DVB-C) and press OK .
4. Select the DVB setting you want.
5. Press

, repeatedly if necessary, to close the
menu.
DVB-C channel installation
For ease of use, all DVB-C settings are set to
automatic.
If your DVB-C provider gave you specific DVB-C
values, the network ID or network frequency, enter
these values when the TV asks for them during
installation.
It might be necessary to adjust the scanning (full or
quick scan) or enter a specific symbol rate in the
Settings menu while installing. To set a Symbol rate ,
first set the Symbol rate to Manual .
Channel number conflicts
In some countries, different TV channels
(broadcasters) might have the same channel number.
While installing, the TV shows the list with channel
number conflicts. You need to select which TV
channel you want to install on a channel number with
multiple TV channels.
DVB-T + DVB-C
If you can use a DVB-T antenna input but also a DVB-
C input, you can set up your TV for both DVB-T and
DVB-C. Install one system followed by the other with
the necessary settings.
Once each system is installed, you need to switch the
antenna input signal on the
Antenna connection on
the back of the TV and set the TV in the appropriate
system to view the installed channels on TV.
To select the DVB-T or DVB-C setting, see above.
DVB settings
Access DVB settings
1. Press

and select Setup and press OK .
2. Select Search for channels and press OK .
3. Select Re-install Channels .
4. Select the country where you install this TV.
5. Select
Cable (DVB-C) .
6. Select Start to search channels , or select Settings
for DVB-C settings .
7. Press

, repeatedly if necessary, to close the
menu.
Symbol rate mode
If your cable provider did not give you a specific
symbol rate value to install the TV channels, leave the
Symbol rate mode setting on Automatic .
If you received a specific symbol rate value, select
Manual . However, the value you received could be in
the predefined list of symbol rates already. Select
Predefined symbol rates to check if your value is
available automatically.
Symbol rate
With the Symbol rate mode set to Manual , you can
enter the symbol rate value you received from your
cable provider. To enter the value, use the number
keys.
22