PGO Bug Rider BR-250 Service Manual Download

Page: 112 / 121

. COOLING SYSTEM

BR & M2 250 ENGINE

Connect the upper and lower hoses and secure
them with hose bands.
Connect the thermostatic switch wire and fan
motor wire couplers.

Connect the overflow tube and secure with the
tube clamp.
Fill the radiator with coolant. (

3-9)

Connect the vent tube to the radiator filler.
After installation, check for coolant leaks.

Install the front upper cover.

Air Vent Tube

Radiator

Upper Hose

Overflow Tube

Lower Hose

Bolts

Thermostatic Switch Wire

Nuts

If you want to refill the coolant , the
following procedure must be checked.
1. Please make the radiator filler and the

air vent tube to be separated.

2. Then start the engine , filled in the coolant

till the coolant flowed out from the air
vent tube.

3. Put the air vent tube on.

＊

Summary of Contents for Bug Rider BR-250


























































































































Search results

Summary of Contents for Bug Rider BR-250

Reviews:

Related manuals for Bug Rider BR-250

Brands by name

Popular brands

PGO Bug Rider BR-250, Service Manual

Search results

Summary of Contents for Bug Rider BR-250

Reviews:

Related manuals for Bug Rider BR-250

Brands by name

Popular brands