PGO Bug Rider BR-250 Service Manual Download

Page: 92 / 121

. A.C. GENERATOR/STARTER CLUTCH

BR & M2 250 ENGINE

Disconnect the water hoses from the right
crankcase cover.
Remove the nine bolts attaching the right
crankcase cover and the cover.

STATOR REMOVAL

Remove the two pulser coil attaching screws and
the pulser coil.
Remove the three A.C. generator stator bolts
and the stator.

FLYWHEEL REMOVAL

Hold the flywheel with a flywheel holder and
remove the flywheel nut.

Remove the flywheel with a flywheel puller.

STARTER CLUTCH

REMOVAL

Water Outlet Hose

Bolts

Flywheel

Nut

Flywheel Holder

When removing the pulser coil and stator,
be careful not to damage them to avoid
shorted or broken wire.

＊

Water Inlet Hose

Screws

Bolts

Pulser Coil

A.C. Generator Stator

Flywheel Puller

Summary of Contents for Bug Rider BR-250


























































































































Search results

Summary of Contents for Bug Rider BR-250

Reviews:

Related manuals for Bug Rider BR-250

Brands by name

Popular brands

PGO Bug Rider BR-250, Service Manual

Search results

Summary of Contents for Bug Rider BR-250

Reviews:

Related manuals for Bug Rider BR-250

Brands by name

Popular brands