Pentax K10D 76830 Page 27 Service Manual Download

Page: 27 / 69

13. [ADJUST] POSITIONING SI-LED

[Required equipment]

Power supply, lead wires

①

Solder and arrange the lead wires on 0-O170 as shown in the figure below.

[Caution]

Do not stress to the lands of 0-O170.

②

Apply DC3.2V to 0-O170, and confirm the positioning

And lighting of SI-LED 11points.

③

[ADJ-1]

Loosen 2 screws, and then adjust the position of 0-O170.

④

Tighten 2 screws, and then confirm the position again.

⑤

[

ADJ-2]

Turn adjusting screw to adjust fine adjustment for up

and down position then confirm the position again.

⑥

After adjustment is done, apply the screw-lock to 5 points

and remove the lead wires from 0-O170.

⑦

A mount cover is attached in order to protect a SI-LED part hitting during work.

14. 0-O100

①

Apply small amount of dia bond (Black) as shown in figure.

②

③

M2 prism -- Make sure that there is no dust on M2.

④

0-O100

⑤

TY-CNL-F1.7x3.0 x2 -- Temporally tighten screws while

holding 0-O100 plate.

: SI-LED AF frame

(+)

DC3.2V

(-)

0-O170

①

②

ADJ

⑤

⑥

ADJ

③

⑥

⑦

①

②

③

④

⑤

[Note of Disassembly]

1. Remove the screw lock which is stick to the screw.
2. Unscrew (x2) while pressing the plate of 0-O100.
3. If M2 does not replace, you do not necessary to disassemble.

Summary of Contents for K10D 76830






































































Search results

Summary of Contents for K10D 76830

Reviews:

Related manuals for K10D 76830

Brands by name

Popular brands

Pentax K10D 76830, Service Manual

Search results

Summary of Contents for K10D 76830

Reviews:

Related manuals for K10D 76830

Brands by name

Popular brands