Pentax K10D 76830 Page 28 Service Manual Download

Page: 28 / 69

15. [ADJUST] POSITIONING 0-O100 (VIEWFINDER INDICATIONS)

Preparation: O100 cable for 76830, O100 positioning jig for 76700, Power supply (8V, 3A).

15-1 Preparation

①

Connect the 0-O100 cable for 76830 to the jig as shown figure.

②

Connect the flex board of 0-O100 to the cable.

③

Apply 6.0 V to the jig.

④

Turn the main SW ON.

⑤

Turn the mode SW ON.

*Indication of O100 is display

15-2 Adjustment

①

[Confirmation] Check whether the position of the display is straight.

②

[Adjustment] Loosen the screw and change the position.

③

After adjustment is done, apply screw lock.

16. 0-M100

Preparation: Hexagonal screwdriver 1.5mm

①

0-M100 (when replacing 0-M100 put M125 at sensor side)

[Caution]

There is no dust and stain on the surface of lens.

②

TY-CNL-D1.7x4.0 (x3)

[ADJ]

Temporary adjustment of AF block --- Screw in 3

adjusting screws until they stops, then screw back two turns.

[NOTE]

After CCD position adjustment with programmed

software is done, Apply screw-lock agent to between the
head of adjustment screws and washers.

③

DC6V

①

⑤

④

MAIN

②

①

②

③

②

①

③

M125

Summary of Contents for K10D 76830






































































Search results

Summary of Contents for K10D 76830

Reviews:

Related manuals for K10D 76830

Brands by name

Popular brands

Pentax K10D 76830, Service Manual

Search results

Summary of Contents for K10D 76830

Reviews:

Related manuals for K10D 76830

Brands by name

Popular brands