background image

I. Warning 

To avoid fire or electrical shock, do not expose this product to rain or moisture. 
Do not flash at high level output continuously for over 15 times. 
To avoid short circuit,  make sure the batteries are securely packed so that the contacts 
do  not  touch  each  other  and  take  care  not  to  short  circuit  the  batteries  when  handling 
them. 
Please  place  the  batteries  and  any  other  small  parts  that  can  be  swallowed  mistakenly 
away from children. Contact a doctor immediately if this happens. 
To avoid possible injury to eyes, do not use the flash light close to the eyes. 
Do  not  use  the  flash  light  on  the  people  who  have  medical  conditions  that  might  be 
aggravated by this without first consulting a doctor. 
Please remove the batteries from the flash light and stop using immediately in case of: 

  It is dropped or otherwise seriously damaged so that inner components are revealed. 

  If  the  battery  leaks  corrosive  liquids  or  chemicals,  please  take  out  the  battery  with 

gloves. 

  The product gives off strange smell, smokes or becomes very hot. 

Do not disassemble or maintain this product. Touching the internal high voltage circuits
will cause serious electrical shock. 

Summary of Contents for YN560

































Reviews: