Pentax K10D 76830 Page 55 Service Manual Download

Page: 55 / 69

28-4. AF shift adjustment (Optional)

*If AF does not improve by AF focus adjustment and there is no other factor,
execute AF shift adjustment if necessary.

①

Click

□

button as shown in fig.

②

Input [AFS] by capital letter and press [Enter] key.

③

[afs] will be displayed on tool bar.

④

When click [afs] button, below AF shift screen will be displayed.

⑤

Move the cursor right or left to change the value of AF shift. (+: shift to front side, -: shift to back side)

⑥

Click [Input] to adjust. (Can not input more than ±100um)

28-5. Procedure for Ending the program soft

①

Click “Cl”icon and disconnect the correspond with camera. (USB close)

[Confirm]

[Unconnect] is displayed on USB IO.

*Finish the Program soft with the same procedure of K100D.

Unconnect

76830

Data of camera

Value for

shift

Summary of Contents for K10D 76830






































































Search results

Summary of Contents for K10D 76830

Reviews:

Related manuals for K10D 76830

Brands by name

Popular brands

Pentax K10D 76830, Service Manual

Search results

Summary of Contents for K10D 76830

Reviews:

Related manuals for K10D 76830

Brands by name

Popular brands