manualshive.com logo in svg

Pentax 203125 - PocketJet II B/W Direct Thermal Printer, User Manual

Share
Download
Pentax 203125 - PocketJet II B/W Direct Thermal Printer User Manual Download Page 15

Page 7 

DIP Switch Functions (Control Modes) 

There are four control modes and one control function available.  Turn 
the printer off, select the mode(s) you desire (see page 20 & 21 for 
details) using the DIP switches on the bottom of the printer as explained 
below (See Figures 6a-c below), then turn the printer back on.  Note 
that the DIP switches are all set to the ON position at the factory as 
default positions. 

SW1 - Self Print

 

 

FIGURE 6a. 

 
This mode allows you to print a test page consisting of a repeating 
pattern of various-density bars down to the end of the page.  Set DIP 
switch 1 to OFF to enable the self-print function.  Note that the test 
page size is US Letter. 

 

SW2 – Paper Set Control 

 

FIGURE 6b.

 

If this switch is in the OFF position, paper in the printer will not be 
moved when the printer is powered up. This is for using roll paper.  If 
this switch is in the ON position, paper in the printer will be moved into 
position when the printer is powered up.  This is for using cut sheet 
paper.

 

 

SW3 - Auto-Off Timer 

 FIGURE 6c. 

 
This mode applies only when the printer is powered by the NiMH 
battery.  It allows you to turn the Auto-Off Timer on or off.  In the ON 
position, it will turn the printer off after 120 seconds of no activity.  In 
the OFF position, the printer will stay on until the battery is drained.  
The default is ON.   

 

SW4 - Cleaning Mode 

 

FIGURE 6d. 

 
DIP switch 4 is set to OFF to allow you to clean the PocketJet print 
head and maintain quality printing.  You must use the black felt 
cleaning paper that came with your printer.  The default switch setting 
is ON (cleaning mode is OFF).   
 

NOTE:  In this mode, the other three switches have no effect.  You 

may leave them in previously set positions. 

Summary of Contents for 203125 - PocketJet II B/W Direct Thermal Printer











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands