Pentax 203125 - PocketJet II B/W Direct Thermal Printer User Manual Download Page 13

Page: 13 / 74

Page 5

Indicator Lights

The three indicator lights—POWER, DATA, and BATTERY— show
both normal operation and error conditions.

• Red POWER light is steady: Power is on.
• Red POWER light is blinking: An error has occurred.

• Green DATA light is steady: Unprinted data is in the printer buffer or

a command has been received from the computer.

• Green DATA light is blinking: Printer is receiving data.

• Green BATTERY light is steady: The battery charge is high or the

battery is being discharged.

• Green BATTERY light is blinking: The battery charge is low or the

battery is being charged.

Chapter 5, “Reference,” contains a table with all combinations of
indicator lights and their meanings.

DIP Switches

Four DIP switches control how the printer works. Follow these steps to
make sure the switches are set correctly.

Checking DIP Switches

1. Set the printer face down so that the battery compartment is towards

you.

2. Find the set of four DIP switches marked SW1 on the bottom of the

printer. See Figure 5.

FIGURE 5. Checking the printer’s DIP switches

3. Check the settings of the DIP switches.

NOTE: At the factory all DIP switches are set to ON (up). For a

table listing the function of each DIP switch, see next
page.

Summary of Contents for 203125 - PocketJet II B/W Direct Thermal Printer











































































Search results

Summary of Contents for 203125 - PocketJet II B/W Direct Thermal Printer

Reviews:

Related manuals for 203125 - PocketJet II B/W Direct Thermal Printer

Brands by name

Popular brands

Pentax 203125 - PocketJet II B/W Direct Thermal Printer, User Manual

Search results

Summary of Contents for 203125 - PocketJet II B/W Direct Thermal Printer

Reviews:

Related manuals for 203125 - PocketJet II B/W Direct Thermal Printer

Brands by name

Popular brands