Pentair Siata V132 SFE Installer Manual Download

Page: 2 / 88

Installer manual Siata V132 - SFE - Table of contents

2 / 88

Ref. MKT-IM-003 / B - 19.04.2017

Table of contents

Generalities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1.

Scope of the documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2.

Release management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.3.

Manufacturer identifier, product . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.4.

Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.5.

Abbreviations used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.6.

Norms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.6.1.

Applicable norms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.6.2.

Available certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.7.

Procedure for technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.8.

1.9.

Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.1.

Safety pictograms definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.2.

Safety tags location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

2.3.

Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.1.

Personnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.3.2.

Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4.

Hygiene and sanitization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4.1.

Sanitary issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4.2.

Hygiene measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1.

Valve versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1.1.

Twin pilots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.1.2.

External connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

3.2.

Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.2.1.

Performance flow rate characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.3.

Outline drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.4.

Description and components location . . . . . . . . . . . . . . . . . . . . . . . 16

3.4.1.

Valve with twin pilots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.4.2.

Valve with external pilots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.5.

System regeneration cycle (4-cycle operation) . . . . . . . . . . . . . . . . 18

3.6.

Options available on the valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Summary of Contents for Siata V132 SFE

























































































Search results

Summary of Contents for Siata V132 SFE

Reviews:

Related manuals for Siata V132 SFE

Brands by name

Popular brands

Pentair Siata V132 SFE, Installer Manual

Search results

Summary of Contents for Siata V132 SFE

Reviews:

Related manuals for Siata V132 SFE

Brands by name

Popular brands