INTELLIFLO
XF
®
and INTELLIPRO
XF
®
Variable Speed Pump Installation and User’s Guide
13
12
Pump Menu: Speeds 1-8
Set Speeds 1-8 in Schedule Mode
In Schedule mode, Speeds 1-8 can be programmed
to run a certain speed at a certain time of day. To run
a scheduled speed, press Start/Stop. The screen will
display “Running Schedules” when it is ready to run
a scheduled speed. If Start/Stop is pressed while a
scheduled speed is running, “Running Speed _” will be
displayed (see far left image).
1.
Press
Menu
.
2. Use
Up
or
Down
arrows to scroll to “Speed 1-8”,
then press
Select
.
3. Use
Up
or
Down
arrows
and press
Select
for the
speed you wish to set and schedule.
4.
Press
Select
(display will be highlighted) and
scroll to “Schedule”.
5.
Press
Enter
.
6. Press
Down
arrow (“Set Speed” will display) and
press
Select
to change. Use the
Up
or
Down
arrow to adjust speed.
7. Press
Enter
to save the new speed.
8.
Press the
Down
arrow again, “Set Start Time” will
display.
Press
Select
-
the cursor will highlight the
minute column.
9. Use the
Up
or
Down
arrow to change the time
and the
Left
or
Right
arrow to move cursor from
minutes to hours.
10.
Press
Enter
to save the new start time setting.
11.
Press
Down
arrow - “Set Stop Time” will display. P
ress
Select
. Repeat Steps 8-9 to set stop time.
12.
Press
Enter
to save the new stop time setting.
13.
Press
Start/Stop
.
The IntelliFloXF
®
Variable Speed Pump will prime and
begin to run the programmed schedule at the specified
start time.
When running in Schedule or Egg Timer mode, the
countdown time (T 00:01) showing the hours and
minutes remaining is displayed.
Note:
The pump will not run the scheduled speeds until the
Start/Stop
button is pressed (LED on) to place the pump in
Schedule mode.
Note:
When two speeds are scheduled during the same run
time the pump will run the higher RPM Speed regardless of
Speed # in use.
Note:
The most recent command, Manual or Schedule, takes
priority regardless of speed number RPM.
Programming Schedule for Constant Run
A speed cannot be programmed with the same start
and stop times. To run a speed without stopping, set
the Start time one minute after the stop time.
Example: A single speed will run non stop if programmed
with a Start Time of 8:00 AM and a Stop time of 7:59 AM.
Pump Menu: External Control
External Control
This function is for programming speeds that will run
when the IntelliComm
®
Communication Center sends it a
command. For example, Terminal 3 and 4 in IntelliComm
system will correspond to External Control Program #1.
(5 and 6 to Ext Ctrl #2). Use the External Control feature
to program the IntelliComm system power center.
To access the External Control menu:
1. Check that the green power LED is on.
2. Press the
Menu
button.
3. Use
Up
or
Down
arrow to scroll to “Ext. Ctrl.”.
5. Press
Select
. “Program 1” is displayed.
6. Press
Select
to change the speed. The “RPM”
number will highlight.
7. Press
Up
or
Down
arrow to change the RPM
setting.
8. Press
Enter
to save the setting.
Note:
To cancel any changes, press the
Escape
button to exit without saving.
9. Press
Escape
to return to set Program 2.
10. Use
Up
or
Down
arrow to scroll to “Program 2”.
11. Repeat Steps 6 through 10 to set Program 2, 3,
and 4.
Setting Schedule Mode
Display During Schedule Mode
12:15p
Set Speed
Schedule
12:15p
750 RPM
T 1:05 150 WATTS
Running Speed 1
EXT CONTROL
MENU
MENU
SPEED 1-8
