manualshive.com logo in svg

PAW FC4.13, Manual For Specialised Craftsman

Share
Download
PAW FC4.13 Manual For Specialised Craftsman Download Page 33

33

en

6 

Index

B
Balance values .........................................................................................................................  16
Blocking protection ...............................................................................................................  21
C
Circulation ...............................................................................................................................  21
Circulation pump offset ........................................................................................................  23
Circulation sensor .................................................................................................................  22
Commissioning menu ............................................................................................................  14
Controller commissioning menu ........................................................................................  14
D
Data logging .............................................................................................................................  25
E
Emergency operation ............................................................................................................  18
F
Firmware updates ..................................................................................................................  25
Formatting the SD card ........................................................................................................  26
Fuse, replacing of ....................................................................................................................  29
H
Hot water set temperature .................................................................................................  18
L
Loading controller adjustments ..........................................................................................  26
M
Mains connection .....................................................................................................................  6
Manual mode ...........................................................................................................................  26
Measured values .....................................................................................................................  16
Menu structure .......................................................................................................................  13

O
Offset ........................................................................................................................................  27
Operating hours counter .....................................................................................................  16
Operating mode, relays .........................................................................................................  26
P
Parallel relay ............................................................................................................................  27
R
Relay / sensor  allocation ..........................................................................................................  7
S
Sensor fault, error message .................................................................................................  17
Service ......................................................................................................................................  17
Sliding set value ......................................................................................................................  20
Storing controller adjustments ...........................................................................................  26
Stratified return ......................................................................................................................  24
T
Technical data ............................................................................................................................  4
Troubleshooting ......................................................................................................................  29
U
User code ................................................................................................................................  27

Summary of Contents for FC4.13





































Reviews:

No comments

Brands by name

Popular brands

Load more brands