manualshive.com logo in svg

PAW FC4.13, Manual For Specialised Craftsman

Share
Download
PAW FC4.13 Manual For Specialised Craftsman Download Page 15

15

en

8.  Completing the commissioning menu:

 

Î

In order to save the adjustments, select Save. 
The controller is then ready for operation 
and normally the factory settings will give 
close to optimum operation.

 

Î

In order to get back to the commissioning 
menu channels, press button 

➆

.

The adjustments carried out during commission-
ing can be changed anytime in the corresponding 
adjustment channel.

3 

Heat transfer controller adjustments

3.1 

 Main  menu

In this menu, the different menu areas can be selected. 
The following menus are available:

Status
Store loading
Afterheating
Circulation
Strat. return
Basic settings
SD card
Manual mode
User code
In-/Outputs

Note: 
If no button is pressed for the adjustable time T-display standby, the dis-
play illumination goes out. After 3 more minutes, the controller switches 
to the Status / Store  loading. menu. 

 

Î

In order to get from the Status / Store  loading menu into the main 
menu, press button 

➆

 twice!

3.2 

 Status  menu

In the Status menu of the controller, the status messages for every menu area can 
be found.

Summary of Contents for FC4.13





































Reviews:

No comments

Brands by name

Popular brands

Load more brands