manualshive.com logo in svg

PAW FC4.13, Manual For Specialised Craftsman

Share
Download
PAW FC4.13 Manual For Specialised Craftsman Download Page 29

29

en

Directional pad flashes red. 

Sensor fault. The error code !Sensor fault is 

displayed instead of a temperature on the sensor 
display channel. 

5 

Troubleshooting

If a malfunction occurs, a message will appear on the display of the controller.

fuse

The controller is protected by a fuse. The fuse holder (which also holds the spare 
fuse) becomes accessible when the cover is removed. To replace the fuse, pull the 
fuse holder from the base.

WARNING!

Electric shock!
Upon opening the housing, live parts are exposed!

 

Î

Always disconnect the controller from power supply 
before opening the housing!

The display is permanently off.

Press button 

➄

. Display illuminated?

no

yes

Controller has been in 

standby, everything o.k.

Check the supply line and recon-
nect it.

The fuse of the controller could be 
blown. The fuse holder (which holds 
the spare fuse) becomes accessible 
when the cover is removed. The 
fuse can then be replaced. 

Check the power supply of the controller. Is it disconnected?

no

yes

°C

Ω

Pt1000

°C

Ω

Pt1000

-10

961

55

1213

-5

980

60

1232

0

1000

65

1252

5

1019

70

1271

10

1039

75

1290

15

1058

80

1309

20

1078

85

1328

25

1097

90

1347

30

1117

95

1366

35

1136

100

1385

40

1155

105

1404

45

1175

110

1423

50

1194

115

1442

Short circuit or line break

Disconnected temperature sensors can be 

checked with an ohmmeter. Please check if the 

resistance values correspond with the table.

Summary of Contents for FC4.13





































Reviews:

No comments

Brands by name

Popular brands

Load more brands