Patton SmartNode 4900 User Manual Download Page 76

Page: 76 / 76

Introduction

SmartNode 4900 User Manual

G • Accessories

Introduction

The cables listed in

table 19

are available as accessories for the SmartNode 4900 Series products.

Table 19. Accessory cables

Description

Part Number

DB-25 male to M/34 male cable (Sync serial V.35 port)

1205-25M/35M

DB-15 male to DB-15 male cable (Sync serial X.21 port)

EMEM216006

64-pin telco to open end cable, 6 ft/1.8 m (64-pin FSX port)

10493264-10

50-pin telco to open end cable, 20 ft/6 m

10-3096TM50-20

50-pin telco/16 ends RJ-11 cable, 6 ft/1.8 m

10-3096TM50/16RJ11-6

50-pin telco/16 ends RJ-45 cable, 6 ft/1.8 m

10-3096TM50/16RJ45-6

50-pin telco/50-pin telco cable, 6 ft/1.8 m

10-3096TM50/50-6

DB-25 male to M/34 female cable (Sync serial V.35 port)

1205-25M/35F

DB-15 male to DB-15 female cable, 6 ft/1.8 m (X.21)

EMEF216006

Summary of Contents for SmartNode 4900













































































Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands

Patton SmartNode 4900, User Manual

Search results

Summary of Contents for SmartNode 4900

Reviews:

Related manuals for SmartNode 4900

Brands by name

Popular brands